The Yamaha RIO1608D digital stagebox offers redundant Dante networking over CAT5 to add excellent quality pre-amps to Yamaha Cl and QL-series digital mixing consoles, or other equipment using the Dante protocol. Gain compensation allows the connection of multiple consoles, for stage monitoring etc, without unwanted signal changes.
Specifications
Sampling frequency rate | External | 44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm) / 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm) / 88.2kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm) / 96kHz: +4.1667%, +0.1%, -0.1%, -4.0% |
---|---|---|
Signal delay | Less than 3ms INPUT to OUTPUT, connect with CL5 using Dante, Dante Receive Latency set to 0.25ms (one way), Fs=48kHz | |
Total harmonic distortion | Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, Fs=44.1kHz, 48kHz / Less than 0.05% 20Hz-40kHz@+4dBu into 600Ω, Fs=88.2kHz, 96kHz INPUT to OUTPUT, Input Gain = Min. | |
Frequency response | +0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OUTPUT, Fs=44.1kHz, 48kHz / +0.5, -1.5dB 20Hz-40kHz, refer to +4dBu output @1kHz, INPUT to OUTPUT, Fs=88.2kHz, 96kHz | |
Dynamic range | 108dB typ., INPUT to OUTPUT, Input Gain = Min | |
Hum & noise level | Equivalent input noise | -128dBu typ., Equivalent Input Noise, Input Gain=Max |
Residual output noise | -88dBu Residual output noise, ST master off | |
Crosstalk | -100dB, adjacent INPUT/OUTPUT channels, Input Gain = Min. | |
Power requirements | US/Canada: 120V 60Hz, Japan: 100V 50/60Hz, China: 110-240V 50/60Hz, Korea: 220V 60Hz, Other: 110-240V 50/60Hz | |
Power consumption | 70W | |
Dimensions | W | 480mm (18 7/8in) |
H | 144mm (5 3/4in) | |
D | 361.5mm (14 1/4in) | |
Net weight | 8.8kg (19.4lb) | |
Accessories | Dante Virtual Soundcard license sheet | |
Others | Temperature Range: Operating temperature range: 0 – 40℃, Storage temperature range: -20 – 60℃ |
Analog input characteristics
Input Terminals | GAIN | Actual Load Impedance |
For Use With Nominal |
Input Level | Connector | |
---|---|---|---|---|---|---|
Nominal | Max. before clip | |||||
INPUT 1-32 (Rio3224-D) 1-16 (Rio1608-D) 1-8 (Ri8-D) |
+66dB | 7.5kΩ | 50-600Ω Mics & 600Ω Lines |
-62dBu (0.616mV) | -42dBu (6.16mV) | XLR-3-31 type (Balanced)*1 |
-6dB | +10dBu (2.45V) | +30dBu (24.5V) |
*1. XLR-3-31 type connectors are balanced.(1=GND, 2=HOT, 3=COLD)
*2. In these specifications, 0dBu = 0.775 Vrms.
*3. All input AD converters are 24bit linear, 128times oversampling.
*4. +48V DC ( phantom power ) is supplied to INPUT XLR type connectors via each individual software controlled switch. *5. Rio3224-D only
Analog output characteristics
Output Terminals | Actual Source Impedance |
For Use With Nominal |
Max.Output Level Select SW*4 |
Output Level | Connector | |
---|---|---|---|---|---|---|
Nominal | Max. before clip | |||||
OUTPUT 1-16 (Rio3224-D) 1-8 (Rio1608-D, Ro8-D) |
75Ω | 600Ω Lines | +24dB (default) | +4dBu (1.23 V) | +24dBu (12.3V) | XLR-3-32 type (Balanced)*1 |
+18dB | -2dBu (616mV) | +18dBu (6.16V) |
*1. XLR-3-32 type connectors are balanced.( 1=GND, 2=HOT, 3=COLD )
*2. In these specifications, 0dBu = 0.775 Vrms.
*3. All output DA converters are 24bit, 128times oversampling.
*4. There are switches inside the body to preset the maximum output level. *5. Rio3224-D only
Digital Input & Output Characteristics
Terminal | Format | Data length | Level | Audio | Connector |
---|---|---|---|---|---|
Primary/Secondary | Dante | 24bit or 32bit | 1000Base-T | 24ch Input/32ch Output (Rio3224-D) 8ch Input/16ch Output (Rio1608-D) 8ch Output (Ri8-D) 8ch Input (Ro8-D) |
etherCON Cat5e (Rio3224-D, Rio1608-D) RJ-45 (Ri8-D, Ro8-D) |